Going to NENA next week? Join us in Booth 515.
The ability to summon emergency assistance by using a phone to call 9-1-1 has been ingrained in our society for more than 40 years. For a successful emergency response, it is critical that the responders receive accurate location information. Traditional wired-line telephony is able to use the location of the physical wires as a source of information for caller location, whereas wireless technologies require more exotic mechanisms to locate a 9-1-1 caller.
Current trends expose risks in the emergency response system as we know it:
- More and more 9-1-1 calls being made with mobile devices that are not mapped to a physical phone tied to a physical location in a venue.
- Limited GPS location capability indoors can make it difficult to pinpoint the exact location of a 9-1-1 caller in a multistory building.
Accurate caller location within a building is vital for a timely response to an emergency. With more people using cell phones while indoors, the delays that can occur when emergency responders must rely on outdoor location technologies used inside a building are becoming all too common. This challenge can be compounded in large buildings with many floors and many rooms on each floor.
TCS and Cisco meet this challenge by using the Wi-Fi network to make emergency response faster and more efficient with:
- Seamlessly connection of the cellular and Wi-Fi location control planes, providing results within a few meters of accuracy
- Visibility for accurate mobile 9-1-1 caller location with wireless location mapping specific to the venue
Next week, TCS and Cisco will be presenting this innovation solution at the National Emergency Number Association conference in Nashville, Tennessee.
Come see how we’re disrupting the emergency response space at booth 515. Join us for one of our Buzz Sessions in the NENA Exhibit Hall:
- Monday, 11:45 a.m. – 12:15 p.m.
- Tuesday, 12:00 p.m. – 12:30 p.m.
- Tuesday, 2:45 p.m. – 3:15 p.m.
Tags: 9-1-1, 911, accuracy, assistance, cellular, challenge, Cisco, Conference, control pane, emergency, ERS, GPS, location, map, mobile, NENA, phone, response, smartphone, TCS, wi-fi, wifi, wireless
A lot can change in 25 years. At the first Cisco Live (then known as Networkers conferences) in 1989, 200 geeks gathered for the inaugural event. Fast forward to three weeks ago, when we welcomed a whopping 25,000 attendees into the arms of our namesake, beautiful San Francisco.
We heard there was some interest in how the network performed at the show, so I wanted to share some of the interesting statistics about the network at Cisco Live! I shudder at the thought of the ancient network from 25 years ago. So here we go:
Wi-Fi Client Devices
This year we saw 30,705 unique devices, with 7000 in the theater for John Chambers’ keynote.
# of Unique Clients
# of Sessions
# of Unique Users
# of Unique APs
Avg Users per AP
Max. Concurrent Connected Wi-Fi Devices
There was a peak of 14216 concurrently connected device at SF this year.
Read More »
Tags: #CLUS, 10G, 802.11, access point, analytic, antenna, AP, application, Application Visibility and Control, attendee, AVC, catalyst, Cisco, cisco live, client, client composition, concurrent, Conference, control, controller, deploy, design, device, Gbps, Geek, GHz, HDX, High Availability, high density, infrastructure, IPv6, LAN, laptop, legacy data rate, mobile, moscone, mse, network, networkers, peak, peak throughput, phone, san francisco, show, switch, TBps, TByte, throughput, traffic, unique user, user, visibility, wifi, wireless, wlan
Wi-Fi roaming is often a tumultuous subject. The crux of the issue is, with Wi-Fi the roaming decision is left to the client.
In the recent years, there have been great strides in improving Wi-Fi roaming with the creation of standards-based roaming technologies. Cisco first pioneered fast roaming many years ago with CCKM (Cisco Centralized Key Management), which was the foundation for 802.11r. 11r which was ratified by the IEEE in 2008, allows for fast roaming, even on a secure 802.1X SSID. With 802.11r it is possible to roam without disruption during a voice or video call.
While client support of 802.11r is largely lacking in the laptop space, there is large support in the smartphone realm. Apple iOS devices have supported 11r since iOS 6 (http://support.apple.com/kb/HT5535). The recent Samsung smartphones, such as the Galaxy S4, S5, and Note 3, also support 11r.
Note: Some non-802.11r clients can react adversely when connected to an 11r WLAN. The current recommendation from Cisco is to have a separate WLAN for 802.11r clients.
802.11k is another amendment from the IEEE that helps to improve roaming. 802.11k provides a whole slew of information to the client, which allows the client to understand the RF environment and make an informed roaming decision. This information can include channel load and AP neighbor lists.
11r and 11k help, however, that does not mean the infrastructure is irrelevant in the roaming picture. With the help of a model train, we did some testing to figure out just how much impact the infrastructure could have. We compared Cisco to one of our competitors, whom we will call Vendor A.
This video summarizes the results and shows the train in action, or continue reading for more details:
Read More »
Tags: 11r, 11x, 802.11, 802.11k, 802.11r, 802.11x, access point, AP, channel, channel load, client, dbm, device, infrastructure, rf, roam, roaming, roaming decision, RRM, SSID, standards, statistic, technologies, technology, transit power, video, Voice, wi-fi, wifi, wireless, wlan
Ethernet Switches are broadly categorized into two main categories – Modular and Fixed Configuration.
Modular switches, as the name implies, allows you to add expansion modules into the switches as needed, thereby delivering the best flexibility to address changing networks. Examples of expansion modules are application-specific (such as Firewall, Wireless, or Network Analysis), modules for additional interfaces, power supplies, or cooling fans. Cisco Catalyst 4K and 6K are good examples of Modular switches.
Fixed Configuration switches are switches with a fixed number of ports and are typically not expandable. This category is discussed in further detail below. Cisco Catalyst 2K, 3K and the Cisco 300/500 series are good examples of Fixed Configuration switches.
Let me say up front that there are variations to the categories below as switch makers are constantly adding capabilities and evolving the categories, but the broad essence remains the same.
The Fixed configuration switch category is further broken down into:
– Unmanaged Switches
– Smart Switches
– Managed L2 and L3 Switches
This category of switch is the most cost effective for deployment scenarios that require only basic layer 2 switching and connectivity. As such, they fit best when you need a few extra ports on your desk, in a lab, in a conference room, or even at home.
With some Unmanaged switches in the market, you can even get capabilities such as cable diagnostics, prioritization of traffic using default QoS settings, Energy savings capabilities using EEE (Energy Efficient Ethernet) and even PoE (Power Over Ethernet). However, as the name implies, these switches generally cannot be modified/managed. You simply plug them in and they require no configuration at all.
Cisco 100 Series switches are good examples of this category.
Smart Switches (also known as Lightly Managed Switches):
This category of switches is the most blurred and fastest changing. The general rule here is that these switches offer certain levels of Management, QoS, Security, etc. but is “lighter” in capabilities and less scalable than the Managed switches. It therefore makes them a cost-effective alternative to Managed switches. As such, Smart switches fit best at the edge of a large network (with Managed Switches being used in the core), as the infrastructure for smaller deployments, or for low complexity networks in general.
The capabilities available for this Smart switch category vary widely. All of these devices have an interface for Management – historically a browser-based interface used to be the only way to configure these devices, though nowadays you can manage some of these devices with CLI and/or SNMP/RMON as well. Regardless, these capabilities are lighter than what you will find in their Managed switch counterparts. Smart switches tend to have a management interface that is more simplified than what Managed Switches offer.
Smart switches allow you to segment the network into workgroups by creating VLANs, though with a lower number of VLANs and nodes (MAC addresses) than you’d get with a Managed switch.
They also offer some levels of security, such as 802.1x endpoint authentication, and in some cases with limited numbers of ACLs (access control lists), though the levels of control and granularity would not be the same as a Managed switch.
In addition, Smart switches support basic quality-of-service (QoS) that facilitates prioritization of users and applications based on 802.1q/TOS/DSCP, thereby making it quite a versatile solution.
Cisco 200 Series switches are good examples of this category.
Fully Managed L2 and L3 switches:
Managed Switches are designed to deliver the most comprehensive set of features to provide the best application experience, the highest levels of security, the most precise control and management of the network, and offer the greatest scalability in the Fixed Configuration category of Switches. As a result, they are usually deployed as aggregation/access switches in very large networks or as core switches in relatively smaller networks. Managed switches should support both L2 switching and L3 IP routing though you’ll find some with only L2 switching support.
From a Security perspective, Managed switches provide protection of the data plane (User traffic being forwarded), control plane (traffic being communicated between networking devices to ensure user traffic goes to the right destination), and management plane (traffic used to manage the network or device itself). Managed switches also offer network storm control, denial-of-service protection, and much more.
The Access Control List capabilities allows for flexibly dropping, rate limiting, mirroring, or logging of traffic by L2 address, L3 address, TCP/UDP port numbers, Ethernet type, ICMP or TCP flags, etc.
Managed switches are rich in features that enable them to protect themselves and the network from deliberate or unintended Denial of Service attacks. It includes Dynamic ARP Inspection, IPv4 DHCP snooping, IPv6 First Hop Security with RA Guard, ND Inspection, Neighbor Binding Integrity, and much more.
Additional Security capabilities may include Private VLANs for securing communities of users or device isolation, Secure Management (downloads through SCP, Web-based Authentication, Radius/TACACS AAA, etc), Control Plane Policing (CoPP) for protecting the CPU of the switch, richer support for 802.1x (time-based, Dynamic VLAN Assignment, port/host-based, etc)
From a Scalability perspective, these devices have large table sizes so that you can create large numbers of VLANs (for workgroups), devices (MAC table size), IP routes, and ACL policies for flow-based security/QoS purposes, etc.
For highest network availability and uptime, Managed switches support L3 redundancy using VRRP (Virtual Router Redundancy Protocol), large numbers of Link Aggregation groups (which is used both for scalability and resiliency), and capabilities for protecting L2 such as Spanning Tree Root Guard and BPDU Guard.
When we talk about QoS and Multicast features, the richness of capabilities goes far beyond what you’d see in a Smart Switch. Here you’d see things such as IGMP and MLD Snooping with Querier functions for optimizing IPv4/v6 multicast traffic in the LAN, TCP Congestion Avoidance, 4 or 8 queues to treat traffic differently by importance, setting/tagging traffic by L2 (802.1p) or L3 (DSCP/TOS), and rate limiting traffic.
In terms of Management, things such as multiple ways to configure (using CLI, Web GUI, SNMP Management application), discovering of neighbor devices in the networks (using CDP, LLDP, Bonjour, etc), and troubleshooting capabilities (such as VLAN and Port Mirroring, Traceroute, Ping, Syslog, Cable Diagnostics, RMON, etc) are all included.
What I highlighted is by no means exhaustive, but gives you a sense of what some of the differences may be between Managed and Smart Switches.
Cisco Catalyst and Cisco 300 Series and 500 Series switches are good examples of this category of products.
Managed Switches can go even further than what I’ve highlighted. For example, there’s even richer support for Dynamic Unicast and Multicast Routing protocols, deeper flow intelligence or macro flow statistics with Netflow/SFlow, non-Stop Forwarding capabilities, MPLS/VRF support, Policy enforcement, and many others.
Now, to take a deeper dive into these switch categories and talk about various options, you can select the switches based on:
- Number of ports
- POE versus non-POE
- Stackable versus Standalone
You can find Fixed Configuration switches in Fast Ethernet (10/100 Mbps), Gigabit Ethernet (10/100/1000 Mbps), Ten Gigabit (10/100/1000/10000 Mbps) and even some 40/100 Gbps speeds. These switches have a number of uplink ports and a number of downlink ports. Downlinks connect to end users – uplinks connect to other Switches or to the network infrastructure. Currently, Gigabit is the most popular interface speed though Fast Ethernet is still widely used, especially in price-sensitive environments. Ten Gigabit has been growing rapidly, especially in the datacenter and, as the cost comes down, it will continue to expand into more network applications. With 10GBase-T Ten Gigabit copper interfaces being integrated into LOM (LAN on the Motherboard) and 10G-Base-T switches becoming available now (see the new Cisco SG500XG-8F8T 16-port 10-Gigabit switch), building a Storage or Server farm with 10 Gigabit interfaces has never been easier or more cost-effective. 40G/100G is still emerging and will be mainstream in a few years.
Number of ports:
Fixed Configuration Switches typically come in 5, 8, 10, 16, 24, 28, 48, and 52-port configurations. These ports may be a combination of SFP/SFP+ slots for fiber connectivity, but more commonly they are copper ports with RJ-45 connectors on the front, allowing for distances up to 100 meters. With Fiber SFP modules, you can go distances up to 40 kilometers
POE versus non-POE:
Power over Ethernet is a capability that facilitates powering a device (such as an IP phone, IP Surveillance Camera, or Wireless Access Point) over the same cable as the data traffic. One of the advantages of PoE is the flexibility it provides in allowing you to easily place endpoints anywhere in the business, even places where it might be difficult to run a power outlet. One example is that you can place a Wireless Access Point inside a wall or ceiling.
Switches deliver power according to a few standards – IEEE 802.3af delivers power up to 15.4 Watts on a switch port whereas IEEE 802.3at (also known as POE+) delivers power up to 30 Watts on a switch port. For most endpoints, 802.3af is sufficient but there are devices, such as Video phones or Access Points with multiple radios, which have higher power needs. It’s important to point out that there are other PoE standards currently being developed that will deliver even high levels of power for future applications. Switches have a power budget set aside for running the switch itself, and also an amount of power dedicated for POE endpoints.
To find the switch that is right for you, all you need to do is choose a switch according to your power needs. When connecting to desktops or other types of devices which do not require POE, the non-POE switches are a more cost-effective option.
Stackable versus Standalone:
As the network grows, you will need more switches to provide network connectivity to the growing number of devices in the network. When using Standalone switches, each switch is managed, troubleshot, and configured as an individual entity.
In contrast, Stackable switches provide a way to simplify and increase the availability of the network. Instead of configuring, managing, and troubleshooting eight 48-port switches individually, you can manage all eight like a single unit using a Stackable Switches. With a true Stackable Switch, those eight switches (total 384 ports) function as a single switch – there is a single SNMP/RMON agent, single Spanning Tree domain, single CLI or Web interface – i.e. single management plane. You can also create link aggregation groups spanning across multiple units in the stack, port mirror traffic from one unit in the stack to another, or setup ACLs/QoS spanning all the units. There are valuable operational advantages to be gained by this approach.
Here’s a word of warning. Be careful about products in the market which are sold as “Stackable” when they merely offer a single user interface, or central management interface, for getting to each individual switch unit. This approach is not stackable, but really “clustering”. You still have to configure every feature such as ACLs, QoS, Port mirroring, etc, individually on each switch. Use the following as a proof point – can I create a link aggregation group with one port in one unit of the stack and another port of that group in another unit of the stack? Can I select a port on one unit in the stack and mirror the traffic to a port on another unit of the stack? When I configure an ACL for Security purposes, can I apply that to any port on any unit in the stack? If the answer is “No” to any of these questions, you’re probably not working with a stackable switch.
There are other advantages of True Stacking as well. You can connect the stack members in a ring such that, if a port or cable fails, the stack will automatically route around that failure, many times at microsecond speeds. You can also add or subtract stack members and have it automatically recognized and added into the stack.
Cisco Catalyst 2K-X and 3K or Cisco 500 Series Switches are examples of Switches in this category.
As you can see there’s a multitude of switch options to choose from. So, have a close look at your current deployment and future needs to determine the right switch for your network.
Tags: 10 gigabit, 101, access switch, basics of ethernet, Cisco Switches, Control Plane, core switch, data plane, different kinds, different types, edge switch, ethernet switch, explained, how ethernet works, management plane, network edge, networking basics, options, routers, security, Tutorial, types of switches, understanding different types, what is a network switch, what is ethernet switch, wireless