In recent years, wireless has become the preferred means of access for networks. This change may be have been inevitable to some, but why did this happen? What has changed to make this possible? Not too long ago, there was a time when wireless had the reputation of not having the reliability or performance for everyday use in enterprise networks. But a few events occurred that can be directly attributed to the changed perception of wireless networks.
One event was the Bring Your Own Device (BYOD) movement, which increased the use of Wi-Fi as a means of access. Beside the growth of Read More »
Tags: #wireless, 802.11ac wave 2, beamforming, BYOD (Bring Your Own Device), Cisco ClientLink, Cisco HDX, Cisco Mobility, Cisco Wi-Fi, Cisco Wireless, clean air, enterprise network, reliability, SSO, wi-fi
In my last blog I discussed setting the stage in preparation for the Wi-Fi network for Mobile World Congress 2014 which supported more than 80k devices over a span of 4 days. Today I’ll talk about one of the many site surveys we conducted at the Fira Gran Via to ensure the success of our high density network. Full details in the white paper here.
High Density Wi-Fi deployments and site surveys go hand in hand. Pre-installation and post-installation site surveys account for the most effective way to identify the contours of your RF coverage and eliminate potential multipath distortions, hidden nodes, and other coverage issues. Special attention was given to the large keynote auditorium halls in order to keep a check on the additional RF coverage needs to accommodate the high density of users packed in a very close range.
View of inside the Hall-4 Keynote Auditorium (23000 sq ft) before the Facebook keynote session
Site Survey analysis used to measure the RF coverage in Hall-4 keynote auditorium
The Hall-4 auditorium was one example of such a high density area with the 2000 person capacity area had a peak connection of 1924 concurrently connected Wi-Fi devices distributed across 16 Cisco APs while the Facebook keynote was in progress, with a max load of 530 Mbps of internet traffic. To avoid an RF overlap, the ceiling mounted APs above the auditoriums were converted to monitor mode. Using the final pre-keynote site survey data, the RF profile for the Hall-4 auditorium was tweaked, and RRM automatically optimized the coverage to the desired degree by adjusting the Tx power levels. Read More »
Tags: access point, AP, application, barcelona, beamforming, Cisco, client, coverage, data transfer, deployment, device, Dual Band, event, experience, fira gran via, GHz, HD, HDX, hidden node, high density, hotspot2.0, infrastructure, internet, keynote, mobile world congress, multipath distortion, mwc, network, network operations, radio resource managmeent, rf, RRM, rx-sop, site survey, TB, traffic, traffic pattern, user density, users, wi-fi, wifi, wireless, wireless data transfer
Every year a new attendance record is set at Mobile World Congress by networkers participating from over 200 countries across the globe. This grand attendance of industry-defining vendors, technology enthusiasts and exhibitors triggers an explosive growth in the number of Wi-Fi capable devices being brought to the event. For MWC 2014, Cisco partnered with Fira Gran Via and GSMA to pull off one of the most successful high density Wi-Fi network deployments in the history of global tech events. This blog kicks off a series to provide a glimpse of behind the network, into the design stages, and the course of actions undertaken to implement a robust high density wireless network which served more than 22,000 concurrently connected unique devices and a total of 80,880 devices throughout the event. Full details in whitepaper here.
Setting the Scene
Divided into eight massive exhibition halls, Fira Gran Via covers around 3 million square feet (280,000 square meters) of area which also includes outdoor areas, restaurants, conference rooms, network lounges and a continuous elevated walkway flowing through the entire venue. Higher the environmental complexity, the more fun and challenging it is to achieve the right wireless design for a pervasive network that meets all the needs.
An aerial view of Mobile World Congress 2014 arena at Fira Gran Via, Barcelona
Generally, the physical design of large convention and exhibition halls bear an impish knack of unfavorable conditions for a ubiquitous high density Wi-Fi network, owing mostly to the lofty ceiling heights and construction components. Read More »
Tags: 2.4 GHz, access point, antenna, antennas, AP, architect, barcelona, beamforming, cell isolation, cleanair, ClientLink, convention center, coverage, deployment, design, device, event, fira gran via, GHz, hardware, HD, HDX, high density, infrastructure, interference, management, mobile, mobile world congress, mobility, mwc, network, networking, radio resource management, rf, RRM, rx-sop, site survey, site visit, tech, technology, venue, wi-fi, wifi, wireless
Editor’s Note: This is the second of a four-part deep dive series into High Density Experience (HDX), Cisco’s latest solution suite designed for high density environments and next-generation wireless technologies. For more on Cisco HDX, visit www.cisco.com/go/80211ac. Read part 1 here. Read part 2 here.
The 802.11ac wireless networking standard is the most recent introduction by the IEEE (now ratified), and is rapidly becoming more accepted and reliable industry standard. The good news is that the client and vendor adoption rate for 802.11ac is growing at a much higher pace as compared to when 802.11n was introduced back in 2009. There has been an accelerated growth seen with the mobile and laptop devices entering the wireless market embedded with an 802.11ac WiFi chipset. Unlike in the past, laptop, smartphone and tablet manufacturers are now acknowledging the fact that staying up to date with the latest Wi-Fi standards is as important for the bandwidth hungry users as having a better camera or a higher resolution display.
With the launch of the new 802.11ac AP 3700, Cisco introduces the Cisco HDX (High Density Experience) Technology. Cisco HDX is a suite of solutions aimed towards augmenting the higher performance, more speed and better client connectivity that 802.11ac standard delivers today.
ClientLink 3.0 features as an integral part of Cisco HDX technology designed to resolve the complexities that comes along with the new BYOD trend driving the high proliferation of 802.11ac capable devices.
So what is ClientLink 3.0 technology and how does it work?
ClientLink 3.0 is a Cisco patented 802.11ac/n/a/g beamforming technology Read More »
Tags: 802.11, access point, antenna, AP, beamforming, cell size, Cisco, client, client connectivity, ClientLink, device, downlink, hardware, HD, HDX, high density, IEEE, Industry Standard, LAN, mobile, mobility, network, rf, smartphone, software, solution, tablet, technology, wi-fi, wifi, wireless, wlan
We released our latest in the Fundamentals series earlier this month and it is trending quite well. The 802.11ac standard sounds like a step backwards alphabetically…but it will soon be an incredible step forward forward for WiFi once it is ratified by the IEEE. Watch this latest fundamentals to get comfortable with the truth. 802.11n is still your best bet for 2012 and into 2013 as we continue to partner on the standards process but the future is bright indeed!
Read More »
Tags: 5 GHz, 802.11, 802.11ac, 802.11n, beamforming, cleanair, ClientLink, CTS, IEEE, mobility, mu-mimo, rts, TechWiseTV, VHT, wifi, wireless